 |
 |
|
|
|
Sample NC Program for this 4 Axis Milling Center (Rotate about X Axis) post processor:
% ( / OPERATION COMMENTS) ( / JOB DESCRIPTION :TEST PART) ( / TOOL TABLE SUMMARY) ( / TOOL NUMBER TOOL ID OFFSET NO TOOL COMMENT) ( / 1 FEM_1_2500 1 1/4 FLAT END MILL) ( / 3 SPOT_0_5000 1/2" SPOT DRILL) ( / 4 DRILL_0_1820__14 #14 DRILL .1820 DIAM.) ( / 5 DRILL_0_2010__7 #7 DRILL .2010 DIAM.) ( / 6 TAP_1-4_20 1/4-20 TAP) ( / 11 T0001 .5" FLAT ENDMILL) ( / NC SEQUENCE NAME : ROUGH_FACE) ( / NC SEQUENCE CSYS NAME : G54_CSYS) ( / NC SEQUENCE COMMENTS) ( / ROUGH TOP FACE) ( / SEQUENCE TYPE : FACE MILLING) ( / SPINDLE SPEED : 1500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : FEM_1_2500) ( / TOOL_TYPE : END MILL) ( / TOOL COMMENTS) ( / 1 1/4 FLAT END MILL) ( / CUTTER DIAMETER, 1.250) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 1.250000) ( / LENGTH : 4.000000) ( / LENGTH_UNITS : INCH) ( / NUM_OF_TEETH : 0.000000) ( / TOOL_MATERIAL : -) T01 M06 H1 S1500 M03 G00 X12.5545 Y-6.4872 Z2. M08 Z2.9941 G01 Y1.7628 F10. G02 X13.1671 Y1.7628 I.3063 J0. G01 X13.167 Y-6.4872 G03 X13.7796 Y-6.4872 I.3063 J0. G01 X13.7795 Y1.7628 G02 X14.3921 Y1.7628 I.3063 J0. G01 X14.392 Y-6.4872 G03 X15.0046 Y-6.4872 I.3063 J0. G01 X15.0045 Y1.7628 M09 M05 G00 Z30. X10. Y10. ( / NC SEQUENCE NAME : TRAJECTORY_2) ( / NC SEQUENCE CSYS NAME : NC_CS0) ( / SEQUENCE TYPE : TRAJECTORY MILLING) ( / SPINDLE SPEED : 1200.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : T0001) ( / TOOL_TYPE : END MILL) ( / TOOL COMMENTS) ( / .5" FLAT ENDMILL) ( / CUTTER DIAMETER, 0.500) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.500000) ( / LENGTH : 4.000000) ( / LENGTH_UNITS : INCH) ( / NUM_OF_TEETH : 0.000000) ( / TOOL_MATERIAL : -) T11 M06 H11 S1200 M03 G00 X13.7795 Y-4.1122 Z2. G02 X13.7948 Y-3.9896 Z2.0304 I.5 J0. F5. G01 X14.2795 Y-3.6122 Z2. X14.7795 Y.3878 X13.2795 Y-4.1122 X13.7795 M05 ( / NC SEQUENCE NAME : SPOT_109_141) ( / NC SEQUENCE CSYS NAME : G54_CSYS) ( / NC SEQUENCE COMMENTS) ( / SPOT DRILL HOLES ON FRONT FACE) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 2500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : SPOT_0_5000) ( / TOOL_TYPE : SPOT DRILL) ( / TOOL COMMENTS) ( / 1/2" SPOT DRILL) ( / CUTTER DIAMETER, 0.500, POINT ANGLE, 90.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.500000) ( / LENGTH : 2.000000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 90.000000) ( / TOOL_MATERIAL : -) T03 M06 H3 S2500 M03 G00 X12.5295 Y.1378 Z3.0941 M08 G81 X12.5295 Y.1378 Z2.9341 R3.0941 F8. P400 Y-1.8622 Y-3.8622 G80 M09 M05 G00 Z30. X10. Y10. ( / NC SEQUENCE NAME : DRILL_TOP_HOLES) ( / NC SEQUENCE CSYS NAME : G54_CSYS) ( / NC SEQUENCE COMMENTS) ( / DRILL HOLES ON FRONT FACE) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 2500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : DRILL_0_1820__14) ( / TOOL_TYPE : DRILLING) ( / TOOL COMMENTS) ( / #14 DRILL .1820 DIAM.) ( / CUTTER DIAMETER, 0.182, POINT ANGLE, 118.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.182000) ( / LENGTH : 3.375000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 118.000000) ( / POINT_DIAMETER : 0.000000) ( / TOOL_MATERIAL : HSS) T04 M06 H4 S2500 M03 G00 X12.5295 Y.1378 Z3.0941 M08 G81 X12.5295 Y.1378 Z2.4394 R3.0941 F6. Y-1.8622 Y-3.8622 G80 M09 M05 ( / NC SEQUENCE NAME : DRILLING_1) ( / NC SEQUENCE CSYS NAME : G54_CSYS) ( / NC SEQUENCE COMMENTS) ( / PECK DRILL HOLES ON FRONT FACE) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 3500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : DRILL_0_2010__7) ( / TOOL_TYPE : DRILLING) ( / TOOL COMMENTS) ( / #7 DRILL .2010 DIAM.) ( / CUTTER DIAMETER, 0.201, POINT ANGLE, 118.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.201000) ( / LENGTH : 3.625000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 118.000000) ( / POINT_DIAMETER : 0.000000) ( / TOOL_MATERIAL : HSS) T05 M06 H5 S3500 M03 G00 X12.5295 Y.1378 Z3.0941 M08 G83 X12.5295 Y.1378 Z2.4337 R3.0941 Q.1 F8. Y-1.8622 Y-3.8622 G80 M09 M05 G00 Z30. X10. Y10. ( / NC SEQUENCE NAME : TAPPING_1) ( / NC SEQUENCE CSYS NAME : G54_CSYS) ( / NC SEQUENCE COMMENTS) ( / TAP HOLES ON FRONT FACE) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : TAP_1-4_20) ( / TOOL_TYPE : TAPPING) ( / TOOL COMMENTS) ( / 1/4-20 TAP) ( / CUTTER DIAMETER, 0.250, CHAMFER LENGTH, 0.300, POINT DIAMETER,\) ( 0.000) ( / TOOL OFFSET NUMBER : N/A) ( / CHAMFER_LENGTH : 0.300000) ( / CUTTER_DIAM : 0.250000) ( / LENGTH : 5.000000) ( / LENGTH_UNITS : INCH) ( / POINT_DIAMETER : 0.000000) ( / TOOL_MATERIAL : HSS) T06 M06 H6 S500 M03 G00 X12.5295 Y.1378 Z3.0941 M08 G84 X12.5295 Y.1378 Z2.1941 R3.0941 F25. Y-1.8622 Y-3.8622 G80 M09 M05 ( / NC SEQUENCE NAME : COUNTERSINKING_2) ( / NC SEQUENCE CSYS NAME : G55_CSYS) ( / NC SEQUENCE COMMENTS) ( / SPOT HOLES AT 90 DEGREES) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 2500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : SPOT_0_5000) ( / TOOL_TYPE : SPOT DRILL) ( / TOOL COMMENTS) ( / 1/2" SPOT DRILL) ( / CUTTER DIAMETER, 0.500, POINT ANGLE, 90.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.500000) ( / LENGTH : 2.000000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 90.000000) ( / TOOL_MATERIAL : -) T03 M06 H3 S2500 M03 G00 X13.0295 Y2.6191 A90. Z6.8622 M08 G81 X13.0295 Y2.6191 Z5.7322 R5.9622 F8. P400 A90. G80 G00 Z6.8622 M09 M05 Z30. X10. Y10. A0. ( / NC SEQUENCE NAME : DRILLING_2) ( / NC SEQUENCE CSYS NAME : G55_CSYS) ( / NC SEQUENCE COMMENTS) ( / PECK HOLES AT 90 DEGREES) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 3500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : DRILL_0_1820__14) ( / TOOL_TYPE : DRILLING) ( / TOOL COMMENTS) ( / #14 DRILL .1820 DIAM.) ( / CUTTER DIAMETER, 0.182, POINT ANGLE, 118.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.182000) ( / LENGTH : 3.375000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 118.000000) ( / POINT_DIAMETER : 0.000000) ( / TOOL_MATERIAL : HSS) T04 M06 H4 S3500 M03 G00 X13.0295 Y2.6191 A90. Z6.8622 M08 G83 X13.0295 Y2.6191 Z5.3075 R5.9622 Q.1 F8. A90. G80 G00 Z6.8622 M09 M05 ( / NC SEQUENCE NAME : COUNTERSINKING_3) ( / NC SEQUENCE CSYS NAME : G56_CSYS) ( / NC SEQUENCE COMMENTS) ( / SPOT HOLES AT 270 FACE) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 2500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : SPOT_0_5000) ( / TOOL_TYPE : SPOT DRILL) ( / TOOL COMMENTS) ( / 1/2" SPOT DRILL) ( / CUTTER DIAMETER, 0.500, POINT ANGLE, 90.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.500000) ( / LENGTH : 2.000000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 90.000000) ( / TOOL_MATERIAL : -) T03 M06 H3 S2500 M03 G00 X14.0295 Y-2.6191 A-90. Z2.1378 M08 G81 X14.0295 Y-2.6191 Z1.0078 R1.2378 F8. P400 A-90. G80 G00 Z2.1378 M09 M05 Z30. X10. Y10. A0. ( / NC SEQUENCE NAME : DRILLING_3) ( / NC SEQUENCE CSYS NAME : G56_CSYS) ( / NC SEQUENCE COMMENTS) ( / PECK HOLES AT 270 DEGREES) ( / SEQUENCE TYPE : HOLEMAKING) ( / SPINDLE SPEED : 3500.000000 RPM [CW]) ( / TOOL_ORIENTATION : 90.000) ( / TOOL NAME : DRILL_0_1820__14) ( / TOOL_TYPE : DRILLING) ( / TOOL COMMENTS) ( / #14 DRILL .1820 DIAM.) ( / CUTTER DIAMETER, 0.182, POINT ANGLE, 118.000) ( / TOOL OFFSET NUMBER : N/A) ( / CUTTER_DIAM : 0.182000) ( / LENGTH : 3.375000) ( / LENGTH_UNITS : INCH) ( / POINT_ANGLE : 118.000000) ( / POINT_DIAMETER : 0.000000) ( / TOOL_MATERIAL : HSS) T04 M06 H4 S3500 M03 G00 X14.0295 Y-2.6191 A-90. Z2.1378 M08 G83 X14.0295 Y-2.6191 Z.5831 R1.2378 Q.1 F8. A-90. G80 G00 Z2.1378 M09 M05 %